|
This is very strong and effective bondage device , allowing you all-around access to the person inside . Unlike vacuumdevices from other manufacturers , this one is airtight , so you can enjoy it without the noise of running vacuumcleaner .
How it works : after you get in , the entry zipper gets sealed by rolling the latex tunnel around it . After air is evacuated , you can disconnect the vacuumcleaner .
Standard thickness is 0.4mm , size 90x90x90 cm . No problem making the cube any size you want ( it even doesnt have to be cube ) .
Package includes : latex sack , frame equipped with automatic one-way valve, sealing rod , clamps for fixation of sealing rod , adaptor for vacuumcleaner connection ( fits all vacuumcleaners ).
There is also variety of options , check them out !
Read more
Available options
|
This is very strong and effective bondage device , allowing you all-around access to the person inside . Unlike vacuumdevices from other manufacturers , this one is airtight , so you can enjoy it without the noise of running vacuumcleaner .
How it works : after you get in , the entry zipper gets sealed by rolling the latex tunnel around it . After air is evacuated , you can disconnect the vacuumcleaner .
Standard thickness is 0.4mm , size 90x90x90 cm . No problem making the cube any size you want ( it even doesnt have to be cube ) .
Package includes : latex sack , frame equipped with automatic one-way valve, sealing rod , clamps for fixation of sealing rod , adaptor for vacuumcleaner connection ( fits all vacuumcleaners ).
There is also variety of options , check them out !
|
Vacuum cube - manual
Dear Customer,
You will have lots of fun with latex cube you have just received . However , there are some rules , which need to be adhered to in order to operate it safely . We have prepared few tips for you . Please read them before you use the cube .
SAFETY FIRST :
- never use this type of cube alone . It is very strong bondage device and you may not be able to get out without help from outside , if anything goes wrong .
- Before turning the vacuumcleaner ON , ask for permission from the person inside .
- For case of emergency , establish “stop-signal” with your partner . Whenever this signal is used , partner on outside should immediately release the vacuum and help you to get out . “Stop signal” must NEVER be ignored .
- When you are watching over somebody in cube , never leave him alone , never let him out of sight and always stay within few metres of the cube , so you can intervene in case of need .
BEFORE FIRST USE :
The latex sack of the cube is covered with talcum powder , which protects it during transport and keeps the latex from sticking to itself . Before first use , wash the latex sack with soap and water on both sides , let it dry and then apply latex polish both on inside and outside .
ASSEMBLY :
We recommend that two people do the assembly - one holds up the latex sack , the other assembles the frame . Because the entry opening is small , you need to assemble the frame inside the sack . All parts of the frame are inserted inside via the entry opening . It helps to lubricate the pipes and the inside of the sack with latex polish ( do not use talc on inside of cube - it may cause valve malfunction) .
PREVENT TEARS IN THE LATEX :
- the cube should stand on soft ground ( carpet is perfect .... or lay piece of clotch or latex underneath )
- do no press from above onto the cube ... yen you are insede the cube , you are actually sitting / standing on the ground
- when moving the cube , be gentle . If you drop it on the ground sharply , the corners migh bite thru the latex
SEALING :
Zip up the entrance . Using the aluminium rod , roll up the latex tunnel . Take care to roll it up tightly and without any wrinkles , which may cause air leakage . Then , secure the seal with supplied clamps . Make sure to use thick stripes of latex to underlay under the clamps - this is to protect latex sack from any possible damage by clamps .
AIR EVACUATION :
Attach vacumcleaner to the cube . Ask the person inside for permission to turn it on . Only then turn the vacuumcleaner on . When the air is completely evacuated , disconnect the vacuumcleaner from cube and then turn it off . If you turn the vacuumcleaner off , while still conneced to cube , some air may get back into the cube , because for proper function , the valve needs sudden pressure change .
RELEASING VACUUM :
Simply unroll and unzip the entrance to let the air in.
CLEANING :
After each use , wash the cube with soap and water ( both inside and outside ) . Then let it dry on dark and cool place . After it dries on one side , turn it inside out , so both sides can dry .
IF THE CUBE DOESN´T HOLD VACUUM
If the cube holds vacuum for no more than five minutes or so , you need to find the leak : Check the valve : dip about 2 cm of the narrow end of the valve in the water and try blowing into it from other side . There must be no bubbles coming out of it . If bubbles do come out , try running some water thru it , let it dry completely and then put few drops of silicone oil into it ( from the narrow side ) . Then test it again . Make sure that the sleeve around the valve is wrinkle-freeb .
If you have any problems whatsoever and you don´t find answer in this manual , please feel free to ask questions .
We wish you many pleasant moments with our latex cube
Your Eurocatsuits.com
© Eurocatsuits.com 2006-2024
Made in EU ( Czechia ) . Sold exclusively on Eurocatsuits.com .
All images and videos used on this website are our own and we do not permit their use for commercial purposes anywhere else . If you see any item being offered with same image as ours - its pirated image and the item is fake. We dont sell on Ebay nor Aliexpress ... nor do we buy from there . There is fake vendor on Aliexpress , pretending to be Eurocatsuits - beware .