Nepropusna lateks vakuum kocka
Cijena :740.69 USD
Koliko će iznositi poštarina ?
Status :Proizvod se izrađuje po mjeri nakon narudžbe
airtight latex vacuumcube in metallic black , with stailess steel frame airtight latex vacuumcube in metallic black , with stailess steel frame airtight latex vacuumcube in metallic black , with stailess steel frame airtight latex vacuumcube in metallic black , with stailess steel frame
airtight latex vacuumcube in metallic black , with stailess steel frame airtight latex vacuumcube in metallic black , with stailess steel frame

Ovo je vrlo jaka i učinkovita naprava za bondage, koja vam dopušta pristup osobi unutra sa svih strana. Za razliku od vakuum proizvoda drugih proizvođača, ovaj je nepropustan, tako da možete uživati u njemu bez zvuka uključenog usisivača.

Kako radi: nakon što uđete, ulazni zatvarač se zabrtvi kad smotate lateks tunel oko njega. Nakon što se sav zrak isprazni, možete odvojiti usisivač.

Standardna debljina je 0.4mm, veličina 90x90x90 cm. Nije problem napraviti kocku bilo koje veličine koju želite ( ne mora ni biti kocka ).

Paket uključuje: lateks vreću, okvir s jednosmjernim ventilom, štap za brtvljenje, štipaljke za pričvršćivanje štapa, priključak za usisivač ( pristaje svim usisivačima ).

Postoje i brojne opcije, pogledajte ih!

Read more
Dostupne opcije
Ovo je vrlo jaka i učinkovita naprava za bondage, koja vam dopušta pristup osobi unutra sa svih strana. Za razliku od vakuum proizvoda drugih proizvođača, ovaj je nepropustan, tako da možete uživati u njemu bez zvuka uključenog usisivača.

Kako radi: nakon što uđete, ulazni zatvarač se zabrtvi kad smotate lateks tunel oko njega. Nakon što se sav zrak isprazni, možete odvojiti usisivač.

Standardna debljina je 0.4mm, veličina 90x90x90 cm. Nije problem napraviti kocku bilo koje veličine koju želite ( ne mora ni biti kocka ).

Paket uključuje: lateks vreću, okvir s jednosmjernim ventilom, štap za brtvljenje, štipaljke za pričvršćivanje štapa, priključak za usisivač ( pristaje svim usisivačima ).

Postoje i brojne opcije, pogledajte ih!
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.
airtight latex vacuumcube in metallic black , with stailess steel frame. Click to see full resolution image.


Vacuum cube - manual

Dear Customer,
You will have lots of fun with latex cube you have just received . However , there are some rules , which need to be adhered to in order to operate it safely . We have prepared few tips for you . Please read them before you use the cube .

SAFETY FIRST :
- never use this type of cube alone . It is very strong bondage device and you may not be able to get out without help from outside , if anything goes wrong .
- Before turning the vacuumcleaner ON , ask for permission from the person inside .
- For case of emergency , establish “stop-signal” with your partner . Whenever this signal is used , partner on outside should immediately release the vacuum and help you to get out . “Stop signal” must NEVER be ignored .
- When you are watching over somebody in cube , never leave him alone , never let him out of sight and always stay within few metres of the cube , so you can intervene in case of need .

BEFORE FIRST USE :
The latex sack of the cube is covered with talcum powder , which protects it during transport and keeps the latex from sticking to itself . Before first use , wash the latex sack with soap and water on both sides , let it dry and then apply latex polish both on inside and outside .

ASSEMBLY :
We recommend that two people do the assembly - one holds up the latex sack , the other assembles the frame . Because the entry opening is small , you need to assemble the frame inside the sack . All parts of the frame are inserted inside via the entry opening . It helps to lubricate the pipes and the inside of the sack with latex polish ( do not use talc on inside of cube - it may cause valve malfunction) .

PREVENT TEARS IN THE LATEX :
- the cube should stand on soft ground ( carpet is perfect .... or lay piece of clotch or latex underneath ) - do no press from above onto the cube ... yen you are insede the cube , you are actually sitting / standing on the ground - when moving the cube , be gentle . If you drop it on the ground sharply , the corners migh bite thru the latex

SEALING :
Zip up the entrance . Using the aluminium rod , roll up the latex tunnel . Take care to roll it up tightly and without any wrinkles , which may cause air leakage . Then , secure the seal with supplied clamps . Make sure to use thick stripes of latex to underlay under the clamps - this is to protect latex sack from any possible damage by clamps .

AIR EVACUATION :
Attach vacumcleaner to the cube . Ask the person inside for permission to turn it on . Only then turn the vacuumcleaner on . When the air is completely evacuated , disconnect the vacuumcleaner from cube and then turn it off . If you turn the vacuumcleaner off , while still conneced to cube , some air may get back into the cube , because for proper function , the valve needs sudden pressure change .

RELEASING VACUUM :
Simply unroll and unzip the entrance to let the air in.

CLEANING :
After each use , wash the cube with soap and water ( both inside and outside ) . Then let it dry on dark and cool place . After it dries on one side , turn it inside out , so both sides can dry .

IF THE CUBE DOESN´T HOLD VACUUM
If the cube holds vacuum for no more than five minutes or so , you need to find the leak : Check the valve : dip about 2 cm of the narrow end of the valve in the water and try blowing into it from other side . There must be no bubbles coming out of it . If bubbles do come out , try running some water thru it , let it dry completely and then put few drops of silicone oil into it ( from the narrow side ) . Then test it again . Make sure that the sleeve around the valve is wrinkle-freeb .

If you have any problems whatsoever and you don´t find answer in this manual , please feel free to ask questions . We wish you many pleasant moments with our latex cube

Your Eurocatsuits.com
Ne zaboravite dodati: talk puder ( olakšava odijevanje ) - i sjajilo za lateks ( pojačava prirodni sjaj lateksa )
Talk puder
8.29 USD
Sjajilo za lateks & lubrikant
16.16 USD
Water-based latex lubricant , 600ml
18.47 USD

Tell us what you think !


© Eurocatsuits.com 2006-2019
Made in EU . Sold exclusively on Eurocatsuits.com